Features
Surface Options:
Flat, Bute, Çamsan Bute, NTR, Milled, Glossy, Fresco
Thickness Options:
8mm - 30mm
Size Options:
1830x3660mm - 2100x2080mm
Custom Size:
Your requests will be reviewed.
Category
Stock Code
M1HYHZE8XF
Technical Specifications
Appearance (TS 1770)
- Coated products made from MDFLam and SUNTALam should be free of protrusions and depressions.
- There should be no manufacturing or cutting errors at the edges and corners.
Deviation from Shape and Squareness (TS 1770)
- MDF and chipboard should be in the shape of a rectangular prism, with their corners intersecting at right angles.
- For an edge length of 1000 mm, the deviation from the miter edge should not exceed 2 mm.
- When the width and length exceed 1000 mm, the deviation must remain within the width and length tolerance limits.
Dimensions and Tolerances (TS 1770)
The length and width of MDFLam and SUNTALam products are unrestricted, provided they conform to the module dimensions in TS 2014 and TS 2018. The thickness should not be less than 1.5 mm for wood fiber products and 6 mm for particle board products.
- Thickness tolerance for MDFLam products: ± 0.2 mm
- Width tolerance for MDFLam products: ± 3 mm
- Length tolerance for MDFLam products: ± 5 mm
- Thickness tolerance for SUNTALam products: ± 0.2 mm
- Width tolerance for SUNTALam products: ± 5 mm
- Length tolerance for SUNTALam products: ± 5 mm
Physical and Mechanical Properties (TS 1770)
The physical and mechanical properties of products manufactured from MDFLam and SUNTALam must conform to the values given in the table.
Marking (TS 1770)
The company's registered trademark or abbreviated name, the TS 1770 mark (TM), the name and type of the plate, and the nominal dimensions of the plate (thickness, length, width) in mm are written on the packaging; in packaged sales, in addition to these, the color and pattern of the plate, whether one or two sides are coated, its type, and the number of plates in the package are also written on the packaging.
Packaging (TS 1770)
When packaging MDFLam and SUNTALam panels, their edges should be strapped lengthwise and widthwise with banding to prevent them from falling apart, and corner protectors should be placed where these bands meet to prevent damage to the corners.
| Plate | Thickness (mm) | Width (mm) | Length (mm) |
|---|---|---|---|
| MDF Laminate | ± 0.2 | ± 3 | ± 5 |
| Laminated Chipboard | ± 0.2 | ± 5 | ± 5 |
| Physical and Mechanical Properties | MDF Laminate (KL) - Chipboard Laminate (KY) |
|---|---|
| Crack resistance | There should be no cracking as a result of the test. |
| Resistance to hot containers | The test should not result in any permanent changes other than a decrease in brightness, such as cracking, discoloration, or other alterations. |
| Resistance to cigarette burn | The test should not result in any permanent changes other than a decrease in brightness, such as cracking, discoloration, or other alterations. |
| Stain resistance | The experiment should leave no stains or marks. |
| Wear resistance | (IP+FO > 150) / For 245 gr overlay, > 8000 taber, for 62 gr overlay, > 12000 taber should be required. |
| Scratch resistant. | (IP+FO > 150) / For 245 gr overlay, > 8000 taber, for 62 gr overlay, > 12000 taber should be required. |
Coated Sheet Experiments
| Serial Number | Characteristics | Method | Performance (Standard) | Unit |
|---|---|---|---|---|
| 1 | Element Thickness (t) * Thickness relative to nominal value * Current thickness of the plate | TS EN 14323 | <15 → ±0.3 15 ≤ t ≤ 20 → +0.5 – (-0.3) >20 → ±0.5 t maximum – t minimum ≤ 0.6 | mm |
| 2 | Surface Layer Width (W) | - | ±2.5 | mm |
| 3 | Surface Layer Length (l) * Commercially used measurements * Pre-cut sheets | - | ±5 / ±2.5 | mm |
| 4 | Deviation from the Plane | - | ≤ 2 | mm / m |
| 5 | Side Damages * Commercially used measurements * Pre-cut sizes | - | ≤ 10 / ≤ 3 | mm / m |
| 6 | Surface Defects | - | Dots ≤ 2 / Lines ≤ 20 | mm²/m² - mm/m |
| 7 | Scratch Resistance | - | ≥ 1.5 | N |
| 8 | Resistance to Color Fading | - | ≥ 3 | Classification |
| 9 | Resistance to cracking. | - | ≥ 3 | Classification |
| 10 | Abrasion Resistance | TS EN 13329+A1 | Initial Wear <50 – Wear Resistance <150 | Transfer |
| 11 | Surface Strength | TS EN 311 | ≥ 1.00 | N/mm² |
| 12 | Formaldehyde Release | TS 4894 / EN 120 | For E1, ≤ 8 — For E2, 8 < and ≤ 30 | mg/gr |
| 13 | Resistance to Cigarette Flame | TS EN 438-2 | 4 | Classification |
| 14 | Resistance to Water Vapor | TS EN 438-2 | 4 | Classification |
| 15 | Impact Strength of Large Diameter Balls | TS EN 438-2 | ≥ 1400 | N, mm |
| 16 | Brightness Level | TS EN 14323 | - | - |
| 17 | Color Harmony and Surface Texture | TS EN 14323 | - | Classification |
